Instrumentation Trainer Kits

Displacement Measurement Using LVDT

Code: IT1

LVDT Transducer with Displacement of ± 5mm transparent enclosure. Primary Excitation voltage of Sine wave 1V p-p On-board Digit…

Details Enquire

Pressure Measurement Kit

Code: IT2

Resistive pressure transducer with pressure of 0-300mm HG/ 6PSI transparent enclosure. Primary excitation voltage of 5V DC. On-b…

Details Enquire

Load Measurement Using Strain Gauge Kit

Code: IT3

Resistive load cell is used to measure load up to 3 kgs. Primary excitation voltage of 12V DC. On-board digital panel meter prov…

Details Enquire

Temperature Measure Using Thermocouple

Code: IT4

K-type Thermocouple is used to measure up to 100°C On-board digital panel meter provided. Thermometer for measurement of temper…

Details Enquire

Temperature Measurement Using RTD (PT - 100)

Code: IT5

PT-100 Type RTD sensor is used to measure up to 100°C On-board Digital panel meter provided. Thermometer for measurement of tem…

Details Enquire

LDR / Photo - Transistor Trainer Kit

Code: IT6

LDR or Photo-Transistor is used for light sensing. Output available on 2mm Banana sockets for Monitoring. Relay output for alarm…

Details Enquire

Angular Displacement Kit

Code: IT7

Resistive transducer using multi turn potentiometer to measure angular of 0° to 360°. On- board Digital Panel Meter provided Pr…

Details Enquire

Level Indicator Kit

Code: IT8

Capacitive Level Transducer to measure Level Measurement up to 150mm. On-board Digital Panel Meter provided. Onboard Instrumenta…

Details Enquire

Speed Measurement Kit

Code: IT9

Magnetic Pick-up Transducer is used. Photo Pick up Transducer is also used. On-board Digital Panel Meter provided to measure RPM…

Details Enquire

Thrmistor / AD 590 Kit

Code: IT10

AD590 & Thermistor Sensor is used to measure Temperature up to 100°C. On-board Digital Panel Meter provided Onboard Instrumenta…

Details Enquire

P- PI- PID Controller Simulator Trainer

Code: IT11

Simulated blocks like dead time, integrator, time constant, error detector and gain. Square & Triangle source of 1V p-p (min) at 40Hz…

Details Enquire

Liner System Simulatior Trainer

Code: IT12

Simulated first, second and third order system of type-0 and type-1 Calibrated variable gain amplifier (Resolution 1:1000) Squar…

Details Enquire

Potentiometric Error Detector

Code: IT13

High quality servo-potentiometers of 360° shaft rotation. Built-in signal and power sources. 3 1/2 digits DVM for measurements.…

Details Enquire

Synchro Transmitter- Receiver

Code: IT14

Synchro transmitter-receiver pair with calibrated dials Locking system for receiver rotor Receiver use as control transformer …

Details Enquire

Temperature Controller Trainer Kit

Code: IT15

Temperature controller with facilities for P. I, D and relay control blocks. Operating temperature: Ambient to 90° C. Separate …

Details Enquire

Temperature Sensor Trainer

Code: IT16

Study of 4 different temperature transducers - NTC thermistors, RTD Platinum, K(Cr-Al) thermocouples, IC temperature sensors. Study &…

Details Enquire

DC Motor Speed Control Trainer

Code: IT17

Speed control of a 12V, 4W permanent magnet d.c. motor. Speed range: 0 to 3000 rpm (typical) Opto- interrupter based speed sensi…

Details Enquire

DC- Position Control Trainer

Code: IT18

Position control of a 12V, 1A d.c. gear motor (50rpm) Provision for positive and negative tachogenerator feedback. Tacho constan…

Details Enquire

AC-Position Control Trainer

Code: IT19

2-phase servomotor 12V/ phase, 50Hz, 10W. Power amplifier. Servo potentiometer type error detector. In-built 10.00V (rms) p…

Details Enquire

Relay Control System Trainer

Code: IT20

Square & Sine source of Frequency: 10, 20, 40, 80, 100, 200, 400, 800 and 1000Hz Simulated 2nd order linear plant. Facility for displ…

Details Enquire